Ring Type Joint Flange Supplier

RTJ Flange ASME B16.5 Dimensions, Ring Joint Face Flange, ASME B16.47 RTJ Flange, Female RTJ Flange Manufacturer in India

We as Metalfed Engineering are a prominent supplier and exporter of Ring Type Joint Flanges, which are resistant to a wide range of corrosive media and are not hardened by heat treatment. Uses in springs, truck and trailer bodies, trains, and subways are some of the main applications for this versatile Stainless Steel Ring Type Joint Flanges. It is also used in cars, hubcaps, roof drainage products, table linens, storm door frames, conveyor belts, sinks, subway cars, and home appliances. Hot hardening is not suitable for this Carbon Steel Ring Type Joint Flanges, which can better withstand mechanical forces under room temperature conditions. Annealing should occur at 1850°F – 2050°F followed by rapid cooling.
ASME B16.5 Ring Type Joint Flanges is the ideal choice for applications that require good ductility. The best corrosion resistance of such products is achieved in the annealed condition. It is then heated to 500°F – 900°F to relieve stress and then the material is air-cooled. Solution Heat Treatment (Anneal) for this Class 900 Ring Type Joint Flanges should be up to 1010 degrees C – 1120 degrees C and cool rapidly. It can be found in a variety of applications such as Oil & Gas, Chemical, Fertilizer, Refinery, Petrochemical, Power, Automotive, Bearing, and Mechanical & Structural Equipment.

A Specialized Manufacturer of ANSI B16.5 Ring Type Joint Flange, FN RTJ Flange, FF RTJ Flange, RF Ring Type Joint Flange, AWWA C207 Ring Type Joint Flange, Oval RTJ Flange, Octagonal RTJ Flange in all Dimensions.

Table of Content

ASME B16.5 Ring Type Joint Flange Specifications
ASME B16.5 RTJ Materials and Grades
ASME B16.5 Flanges Types
ANSI B16.5 Ring Type Joint Flange Applications
ASME B16.5 Ring Type Joint Flange Export to

ASME B16.5 Class 150 RTJ Flange Dimensions
ASME B16.5 Class 300 RTJ Flange Dimensions
ASME B16.5 Class 600 RTJ Flange Dimensions
ANSI B16.5 Class 900 RTJ Flange Dimensions
ASME B16.5 Class 1500 RTJ Flange Dimensions
ASME B16.5 Class 2500 RTJ Flange Dimensions

RTJ Flange Gasket may not be suitable for certain demanding forming applications where multiple forming operations are required. Class 1500 Ring Type Joint Flanges has good oxidation resistance at temperatures up to 1550 degrees F but is not recommended for use above 1600 degrees F.

Largest Stockholder of Ring Type Joint Blind Flange, BS10 RTJ Flange, EN 1092-1 RTJ Flange, RTJ Flange JIS 10k 5k, Table E & Table H RTJ Flange, ANSI B16.5 Class 150#, 300#, 600#, 900#, 1500#, 2500# RTJ Flanges, RTJ Flange PN16 at Best Prices.

ASME B16.5 / ASME B16.47 Ring Type Joint Flange Specifications

Product Name:	Ring Type Joint Flange, RTJ Flange
Size Chart:	1/2″ (15 NB) to 48″ (1200NB) DN10~DN5000
Dimensions:	ANSI B16.5, ANSI B16.47 Series A & B, MSS SP44, ASA, API-605, AWWA, Custom Drawings
Pressure Rating ANSI:	Class 150 LBS, 300 LBS, 400 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS
Pressure Calculation in DIN:	PN6 PN10 PN16 PN25 PN40 PN64 / 6Bar 10Bar 16Bar 25Bar 40Bar
Coating/Surface Treatment:	Anti-rust Paint, Oil Black Paint, Yellow Transparent, Zinc Plated, Cold and Hot Dip Galvanized
Connection Type/Flange Face Type:	RF-Raised Face, RTJ-Ring Type Joint, FF-Flat Face, LMF-Large Male-Female, LJF-Lap-Joint Face, SMF-Small Male-Female, Small Tongue, Large Tongue & Groove, Groove
Custom Flange/Special Design:	As per your drawing
Standards:	ANSI/ASME B16.5, B16.47 Series A & B, B16.48, BS4504, BS 10, EN-1092, DIN, ANSI Flanges, BS Flanges, ASME Flanges, EN Flanges, DIN Flanges, ASME/ANSI B16.5/16.36/16.47A/16.47B, GOST Flange, MSS SP44, ISO70051, BS1560-3.1, JISB2220, API7S-43, API7S-15, API605, EN1092
Flange Test:	Direct-reading Spectrograph, X-ray detector, Hydrostatic testing machine, UI trasonic flaw detector, Magnetic particle detector
Flanges Equipment:	Press machine, Pushing Machine, Bending machine, electric bevelling machine, Sand-blasting machine, etc
Manufacturers of:	DIN: DIN 2527, DIN 2566, DIN 2573, DIN 2576, DIN 2641, DIN 2642, DIN 2655, DIN 2656, DIN 2627, DIN 2628, DIN 2629, DIN 2631, DIN 2632, DIN 2633, DIN 2634, DIN 2635, DIN 2636, DIN 2637, DIN 2638 B.S: BS4504 , BS3293, BS1560, BS10 AS 2129: Table D; Table E; Table H ANSI B16.5, ANSI B16.47 Series A & B, MSS SP44, ASA, API-605, AWWA ANSI : ANSI B16.5, ANSI B16.47(API605), MSS SP44, ANSI B16.36, ANSI B16.48 ANSI B16.5, ANSI B16.47, MSS SP44, ANSI B16.36, ANSI B16.48 American standard (ANSI) German (DIN) British Standard (BS) ANSI DIN, GOST, JIS, UNI, BS, AS2129, AWWA, EN, SABS, NFE etc. ASTM A182 Ring Type Joint Flange: -BS Flange, EN Flange, API 6A Flange, ANSI Flange, ASME Flange, DIN Flange, EN1092-1 Flange, UNI Flange, JIS/ KS Flange, BS4504 Flange, GB Flange, AWWA C207 Flange, GOST Flange, PSI Flange The other standard: AWWA C207; EN1092-1, GOST12820, JIS B2220; KS B1503, SABS1123; NFE29203; UNI2276
Test Certificates:	Third Party Inspection Report, 100% Radiography Test Report, Raw Materials Certificate, EN 10204/3.1B, etc.
Material Test Certificates (MTC):	As per EN 10204 3.1 and EN 10204 3.2, TC certifying NACE MR0103, NACE MR0175
Uses & Applications:	Petrochemicals and acids, Nuclear Power, Heavy oil refineries, Bitumen upgraders, Offshore, Piping Projects etc.
Export Network:	Ireland, Oman, Dubai, Indonesia, Egypt, Singapore, Saudi & Arabia, Iran, Ukraine, Canada, USA, Brazil, Spain, Thailand, Korea, India, Peru, etc

Ring Type Joint Flange Materials and Grades

Duplex Steel Ring Type Joint Flange:	ASTM / ASME A/SA 182 F44, F45, F51, F53, F55, F60, F61
Super Duplex Ring Type Joint Flange:	ASTM / ASME A/SA 182 F44, F45, F51, F53, F55, F60, F61
Stainless Steel Ring Type Joint Flange:	ASTM A 182, A 240 F 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H, 904L
Nickel Alloys Ring Type Joint Flange:	ASTM SB564, SB160, SB472, SB162 – Nickel 200 (UNS No. N02200), Nickel 201 (UNS No. N02201), Monel 400 (UNS No. N04400), Monel 500 (UNS No. N05500), Inconel 800 (UNS No. N08800), Inconel 825 (UNS No. N08825), Inconel 600 (UNS No. N06600), Inconel 625 (UNS No. N06625), Inconel 601 (UNS No. N06601), Hastelloy C 276 (UNS No. N10276), Alloy 20 (UNS No. N08020)
Alloys Ring Type Joint Flange:	Alloy 20, Alloy C, Alloy C276, Alloy B2
Carbon Steel Ring Type Joint Flange:	STM / ASME A/SA 105 ASTM / ASME A 350, ASTM A 181 LF 2 / A516 Gr.70 A36, A694 F42, F46, F52
Copper Alloys Ring Type Joint Flange:	ASTM SB 61, SB62, SB151, SB152 – UNS No. C 70600 (Cu-Ni 90/10), C 71500 (Cu-Ni 70/30), UNS No. C 10100, 10200, 10300, 10800, 12000, 12200
Low Temperature Steel Ring Type Joint Flange:	ASTM A350 LF2, LF3, LF6
High Yield Ring Type Joint Flange:	ASTM A694 F42, F52, F60, F65, F70
Alloy Steel Ring Type Joint Flange:	ASTM / ASME A/SA 182 & A 387 F1, F5, F9, F11, F12, F22, F91
Titanium Ring Type Joint Flange:	Gr1, Gr2, Gr3, Gr5, Gr7, Gr11
Brass Ring Type Joint Flange:	2604 / 3602 / H59 / H62 / etc.
Aluminium Ring Type Joint Flange:	2017 / 5052 / 6063 / 6061 / 7075 etc.
Alloy 20 Ring Type Joint Flange:	ASME SB462 / ASTM B462, Carpenter® 20 Alloy, Alloy 20Cb-3
Nimonic Ring Type Joint Flange:	Nimonic 80A, Nimonic 75, Nimonic 90
254 SMO Ring Type Joint Flange:	ASME SA182 / ASTM A182, SMO 254/6Mo, UNS S31254, DIN 1.4547
Other Ring Type Joint Flange Material:	Tin bronze, Alumunum bronze, Lead bronze

Class 150 Ring Type Joint Flange Dimensions

Size in Inch	Size in mm	Outer Dia.	Flange Thickness	Hub OD	Weld Neck OD	Welding Neck Length	RTJ RF Dia	RTJ RF Height	PCD	RTJ Pitch dia	RTJ Depth	RTJ Width	Bore
		A	B	C	D	E	F	G	H	I	J	K	L
1/2	15	90	9.6	30	21.3	46	N/A	N/A	60.3	N/A	N/A	N/A	Refer Note
3/4	20	100	11.2	38	26.7	51	N/A	N/A	69.9	N/A	N/A	N/A
1	25	110	12.7	49	33.4	54	63.5	6.35	79.4	47.63	6.35	8.74
1 1/4	32	115	14.3	59	42.2	56	73	6.35	88.9	57.15	6.35	8.74
1 1/2	40	125	15.9	65	48.3	60	82.5	6.35	98.4	65.07	6.35	8.74
2	50	150	17.5	78	60.3	62	102	6.35	120.7	82.55	6.35	8.74
2 1/2	65	180	20.7	90	73	68	121	6.35	139.7	101.6	6.35	8.74
3	80	190	22.3	108	88.9	68	133	6.35	152.4	114.3	6.35	8.74
3 1/2	90	215	22.3	122	101.6	70	154	6.35	177.8	131.78	6.35	8.74
4	100	230	22.3	135	114.3	75	171	6.35	190.5	149.23	6.35	8.74
5	125	255	22.3	164	141.3	87	194	6.35	215.9	171.45	6.35	8.74
6	150	280	23.9	192	168.3	87	219	6.35	241.3	193.68	6.35	8.74
8	200	345	27	246	219.1	100	273	6.35	298.5	247.65	6.35	8.74
10	250	405	28.6	305	273	100	330	6.35	362	304.8	6.35	8.74
12	300	485	30.2	365	323.8	113	406	6.35	431.8	381	6.35	8.74
14	350	535	33.4	400	355.6	125	425	6.35	476.3	396.88	6.35	8.74
16	400	595	35	457	406.4	125	483	6.35	539.8	454.03	6.35	8.74
18	450	635	38.1	505	457.2	138	546	6.35	577.9	517.53	6.35	8.74
20	500	700	41.3	559	508	143	597	6.35	635	558.8	6.35	8.74
24	600	815	46.1	663	610	151	711	6.35	749.3	673.1	6.35	8.74

NOTE: WN bore is derived from the pipe schedule

Class 300 Ring Type Joint Flange Dimensions

Size in Inch	Size in mm	Outer Dia.	Flange Thickness	Hub OD	Weld Neck OD	Welding Neck Length	RTJ RF Dia	RTJ RF Height	PCD	RTJ Pitch dia	RTJ Depth	RTJ Width	Bore
		A	B	C	D	E	F	G	H	I	J	K	L
1/2	15	95	12.7	38	21.3	51	51	5.54	66.7	34.14	5.54	7.14	Refer Note
3/4	20	115	14.3	48	26.7	56	63.5	6.35	82.6	42.88	6.35	8.74
1	25	125	15.9	54	33.4	60	70	6.35	88.9	50.8	6.35	8.74
1 1/4	32	135	17.5	64	42.2	64	79.5	6.35	98.4	60.33	6.35	8.74
1 1/2	40	155	19.1	70	48.3	67	90.5	6.35	114.3	68.27	6.35	8.74
2	50	165	20.7	84	60.3	68	108	7.92	127	82.55	7.92	11.91
2 1/2	65	190	23.9	100	73	75	127	7.92	149.2	101.6	7.92	11.91
3	80	210	27	117	88.9	78	146	7.92	168.3	123.83	7.92	11.91
3 1/2	90	230	28.6	133	101.6	79	159	7.92	184.2	131.78	7.92	11.91
4	100	255	30.2	146	114.3	84	175	7.92	200	149.23	7.92	11.91
5	125	280	33.4	178	141.3	97	210	7.92	235	180.98	7.92	11.91
6	150	320	35	206	168.3	97	241	7.92	269.9	211.12	7.92	11.91
8	200	380	39.7	260	219.1	110	302	7.92	330.2	269.88	7.92	11.91
10	250	445	46.1	321	273	116	356	7.92	387.4	323.85	7.92	11.91
12	300	520	49.3	375	323.8	129	413	7.92	450.8	381	7.92	11.91
14	350	585	52.4	425	355.6	141	457	7.92	514.4	419.1	7.92	11.91
16	400	650	55.6	483	406.4	144	508	7.92	571.5	469.9	7.92	11.91
18	450	710	58.8	533	457	157	575	7.92	628.6	533.4	7.92	11.91
20	500	775	62	587	508	160	635	9.53	685.8	584.2	9.53	13.49
24	600	915	68.3	702	610	167	749	11.13	812.8	692.15	11.13	16.66

IMP. NOTE: WN bore is derived from the pipe schedule

Class 600 Ring Type Joint Flange Dimensions

Size in Inch	Size in mm	Outer Dia.	Flange Thickness	Hub OD	Weld Neck OD	Welding Neck Length	RTJ RF Dia	RTJ RF Height	PCD	RTJ Pitch dia	RTJ Depth	RTJ Width	Bore
		A	B	C	D	E	F	G	H	I	J	K	L
1/2	15	95	14.3	38	21.3	52	51	5.54	66.7	34.14	5.54	7.14	Refer Note
3/4	20	115	15.9	48	26.7	57	63.5	6.35	82.6	42.88	6.35	8.74
1	25	125	17.5	54	33.4	62	70	6.35	88.9	50.8	6.35	8.74
1 1/4	32	135	20.7	64	42.2	67	79.5	6.35	98.4	60.33	6.35	8.74
1 1/2	40	155	22.3	70	48.3	70	90.5	6.35	114.3	68.27	6.35	8.74
2	50	165	25.4	84	60.3	73	108	7.92	127	82.55	7.92	11.91
2 1/2	65	190	28.6	100	73	79	127	7.92	149.2	101.6	7.92	11.91
3	80	210	31.8	117	88.9	83	146	7.92	168.3	123.83	7.92	11.91
3 1/2	90	230	35	133	101.6	86	159	7.92	184.2	131.78	7.92	11.91
4	100	275	38.1	152	114.3	102	175	7.92	215.9	149.23	7.92	11.91
5	125	330	44.5	189	141.3	114	210	7.92	266.7	180.98	7.92	11.91
6	150	355	47.7	222	168.3	117	241	7.92	292.1	211.12	7.92	11.91
8	200	420	55.6	273	219.1	133	302	7.92	349.2	269.88	7.92	11.91
10	250	510	63.5	343	273	152	356	7.92	431.8	323.85	7.92	11.91
12	300	560	66.7	400	323.8	156	413	7.92	489	381	7.92	11.91
14	350	605	69.9	432	355.6	165	457	7.92	527	419.1	7.92	11.91
16	400	685	76.2	495	406.4	178	508	7.92	603.2	469.9	7.92	11.91
18	450	745	82.6	546	457	184	575	7.92	654	533.4	7.92	11.91
20	500	815	88.9	610	508	190	635	9.53	723.9	584.2	9.53	13.49
24	600	940	101.6	718	610	203	749	11.13	838.2	692.15	11.13	16.66

NOTE: WN bore is derived from the pipe schedule

Class 900 Ring Type Joint Flange Dimensions

Size in Inch	Size in mm	Outer Dia.	Flange Thickness	Hub OD	Weld Neck OD	Welding Neck Length	RTJ RF Dia	RTJ RF Height	PCD	RTJ Pitch dia	RTJ Depth	RTJ Width	Bore
		A	B	C	D	E	F	G	H	I	J	K	L
1/2	15	120	22.3	38	21.3	60	60.5	6.35	82.6	39.67	6.35	8.74	Refer Note
3/4	20	130	25.4	44	26.7	70	66.5	6.35	88.9	44.45	6.35	8.74
1	25	150	28.6	52	33.4	73	71.5	6.35	101.6	50.8	6.35	8.74
1 1/4	32	160	28.6	64	42.2	73	81	6.35	111.1	60.33	6.35	8.74
1 1/2	40	180	31.8	70	48.3	83	92	6.35	123.8	68.27	6.35	8.74
2	50	215	38.1	105	60.3	102	124	7.92	165.1	95.25	7.92	11.91
2 1/2	65	245	41.3	124	73	105	137	7.92	190.5	107.95	7.92	11.91
3	80	240	38.1	127	88.9	102	156	7.92	190.5	123.83	7.92	11.91
4	100	290	44.5	159	114.3	114	181	7.92	235	149.23	7.92	11.91
5	125	350	50.8	190	141.3	127	216	7.92	279.4	180.98	7.92	11.91
6	150	380	55.6	235	168.3	140	241	7.92	317.5	211.12	7.92	11.91
8	200	470	63.5	298	219.1	162	308	7.92	393.7	269.88	7.92	11.91
10	250	545	69.9	368	273	184	362	7.92	469.9	323.85	7.92	11.91
12	300	610	79.4	419	323.8	200	419	7.92	533.4	381	7.92	11.91
14	350	640	85.8	451	355.6	213	467	11.13	558.8	419.1	11.13	16.66
16	400	705	88.9	508	406.4	216	524	11.13	616	469.9	11.13	16.66
18	450	785	101.6	565	457	229	594	12.7	685.8	533.4	12.7	19.84
20	500	855	108	622	508	248	648	12.7	749.3	584.2	12.7	19.84
24	600	1040	139.7	749	610	292	772	15.88	901.7	692.15	15.88	26.97

NOTE: WN bore is derived from the pipe schedule

Class 1500 Ring Type Joint Flange Dimensions

Size in Inch	Size in mm	Outer Dia.	Flange Thickness	Hub OD	Weld Neck OD	Welding Neck Length	RTJ RF Dia	RTJ RF Height	PCD	RTJ Pitch dia	RTJ Depth	RTJ Width	Bore
		A	B	C	D	E	F	G	H	I	J	K	L
1/2	15	120	22.3	38	21.3	60	60.5	6.35	82.6	39.67	6.35	8.74	Refer Note
3/4	20	130	25.4	44	26.7	70	66.5	6.35	88.9	44.45	6.35	8.74
1	25	150	28.6	52	33.4	73	71.5	6.35	101.6	50.8	6.35	8.74
1 1/4	32	160	28.6	64	42.2	73	81	6.35	111.1	60.33	6.35	8.74
1 1/2	40	180	31.8	70	48.3	83	92	6.35	123.8	68.27	6.35	8.74
2	50	215	38.1	105	60.3	102	124	7.92	165.1	95.25	7.92	11.91
2 1/2	65	245	41.3	124	73	105	137	7.92	190.5	107.95	7.92	11.91
3	80	265	47.7	133	88.9	117	168	7.92	203.2	136.53	7.92	11.91
4	100	310	54	162	114.3	124	194	7.92	241.3	161.93	7.92	11.91
5	125	375	73.1	197	141.3	156	229	7.92	292.1	193.68	7.92	11.91
6	150	395	82.6	229	168.3	171	248	9.53	317.5	211.14	9.53	13.49
8	200	485	92.1	292	219.1	213	318	11.13	393.7	269.88	11.13	16.66
10	250	585	108	368	273	254	371	11.13	482.6	323.85	11.13	16.66
12	300	675	123.9	451	323.8	283	438	14.27	571.5	381	14.27	23.01
14	350	750	133.4	495	355.6	298	489	15.88	635	419.1	15.88	26.97
16	400	825	146.1	552	406.4	311	546	17.48	704.8	469.9	17.48	30.18
18	450	915	162	597	457	327	613	17.48	774.7	533.4	17.48	30.18
20	500	985	177.8	641	508	356	673	17.48	831.8	584.2	17.48	33.32
24	600	1170	203.2	762	610	406	794	20.62	990.6	692.15	20.62	36.53

NOTE: WN bore is derived from the pipe schedule

Class 2500 Ring Type Joint Flange Dimensions

Size in Inch	Size in mm	Outer Dia.	Flange Thickness	Hub OD	Weld Neck OD	Welding Neck Length	RTJ RF Dia	RTJ RF Height	PCD	RTJ Pitch dia	RTJ Depth	RTJ Width	Bore
		A	B	C	D	E	F	G	H	I	J	K	L
1/2	15	135	30.2	43	21.3	73	65	6.35	88.9	42.88	6.35	8.74	Refer Note
3/4	20	140	31.8	51	26.7	79	73	6.35	95.2	50.8	6.35	8.74
1	25	160	35	57	33.4	89	82.5	6.35	108	60.33	6.35	8.74
1 1/4	32	185	38.1	73	42.2	95	102	7.92	130.2	72.23	7.92	11.91
1 1/2	40	205	44.5	79	48.3	111	114	7.92	146	82.55	7.92	11.91
2	50	235	50.9	95	60.3	127	133	7.92	171.4	101.6	7.92	11.91
2 1/2	65	265	57.2	114	73	143	149	9.53	196.8	111.13	9.52	13.49
3	80	305	66.7	133	88.9	168	168	9.53	228.6	127	9.52	13.49
4	100	355	76.2	165	114.3	190	203	11.13	273	157.18	11.13	16.66
5	125	420	92.1	203	141.3	229	241	12.7	323.8	190.5	12.7	19.84
6	150	485	108	235	168.3	273	279	12.7	368.3	228.6	12.7	19.84
8	200	550	127	305	219.1	318	340	14.27	438.2	279.4	14.27	23.01
10	250	675	165.1	375	273	419	425	17.48	539.8	342.9	17.48	30.18
12	300	760	184.2	441	323.8	464	495	17.48	619.1	406.4	17.48	33.32

NOTE: WN bore is derived from the pipe schedule

RTJ Flanges Types and Standards

rtj flange en 1092-1
ASME B16.5 rtj flanges
rf ff rtj Flanges
api rtj flanges
copper rtj flanges
rtj flanges class 300
blind rtj flange
rtj orifice flange
rtj pipe flange
rtj raised face flange
rtj flat face flange

female rtj flange
class 150 rtj flange
rtj flange pn 16
weld neck flange rtj
ff rtj flange
150# rtj flange
Aluminium rtj flange
150 LB rtj flange
300 LB rtj flange
fn rtj flange
ansi 1500 rtj flange

rtj flange sch 80
stainless steel rtj flange
rtj flange welding
carbon steel rtj flange
class 600 rtj flange
class 900 rtj flange
ss rtj flange
api 6a rtj flange
ansi 900 rtj flange
jis rtj flange
ansi 600 ring type joint flange

Ring Type Joint Flange Applications & Industries

Oil & Gas Industries

Gas Processing Industries

Food Processing Industries

Petrochemical Industries

Chemical Industries

Power Generation Industries

Sugar Industries

Fertilizers Industries

We are well-known prestigious Manufacturers, Exporters, and Suppliers of high quality ASME B16.5 Ring Type Joint Flange. We supply ASME B16.47 Ring Type Joint Flange to customers in various industries including chemical, pharmaceutical, petrochemical, power, engineering and various other industrial applications. Test Certificate as per EN 10204 / 3.1B, Raw Materials Certificate, Third Party Inspection Report and 100% Radiography Test Report.

Ready Stock of Ring Type Joint Flange Export to

AfricaAlgeria, Angola, Benin, Botswana, Burkina Faso, Burundi, Cabo Verde, Cameroon, Central African Republic (CAR), Chad, Comoros, The Democratic Republic of the Congo, Republic of the Congo, Cote d’Ivoire, Djibouti, Egypt, Equatorial Guinea, Eritrea, Ethiopia, Gabon, Gambia, Ghana, Guinea, Guinea-Bissau, Kenya, Lesotho, Liberia, Libya, Madagascar, Malawi, Mali, Mauritania, Mauritius, Morocco, Mozambique, Namibia, Niger, Nigeria, Rwanda, Sao Tome and Principe, Senegal, Seychelles, Sierra Leone, Somalia, South Africa, South Sudan, Sudan, Swaziland, Tanzania, Togo, Tunisia, Uganda, Zambia, Zimbabwe

EuropeAlbania, Andorra, Armenia, Austria, Azerbaijan, Belarus, Belgium, Bosnia and Herzegovina, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Kazakhstan, Kosovo, Latvia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Malta, Moldova, Monaco, Montenegro, Netherlands, Norway, Poland, Portugal, Romania, Russia, San Marino, Serbia, Slovakia, Slovenia, Spain, Sweden, Turkey, Ukraine, United Kingdom, Vatican City

AmericaAntigua and Barbuda, Bahamas, Barbados, Belize, Canada, Costa Rica, Cuba, Dominica, Dominican Republic, El Salvador, Grenada, Guatemala, Haiti, Honduras, Jamaica, Mexico, Nicaragua, Panama, Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Trinidad and Tobago, United States of America, Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Suriname, Uruguay, Venezuela

Asia/OceaniaAfghanistan, Armenia, Azerbaijan, Bahrain, Bangladesh, Bhutan, Brunei, Cambodia, China, Cyprus, Georgia, India, Indonesia, Iran, Iraq, Israel, Japan, Jordan, Laos, Lebanon, Malaysia, Maldives, Mongolia, Myanmar (Burma), Nepal, North Korea, Oman, Pakistan, Palestine, Philippines, Qatar, Russia, Saudi Arabia, Singapore, South Korea, Sri Lanka, Syria, Taiwan, Tajikistan, Thailand, Timor-Leste, Turkey, Turkmenistan, United Arab Emirates (UAE), Uzbekistan, Vietnam, Yemen, Australia, Fiji, Kiribati, Marshall Islands, Micronesia, Nauru, New Zealand, Palau, Papua New Guinea, Samoa, Solomon Islands, Tonga, Tuvalu, Vanuatu

CONTACT

Please send us the complete details of Ring Type Joint Flange requirement. We offer ANSI B16.5 Ring Type Joint Flange, and ASME B16.5 RTJ Flanges which are accurately designed to provide satisfaction to our customers. We are assisted by a team of skilled professionals, who support us in all our career activities right from a realization of raw material to testing and final dispatch of these Class 150#, 300#, 400#, 600#, 900#, 1500#, 2500#, Ring Type Joint Flange at our valuable customers end. Buy Ring Type Joint Flangeat a cheap price from us.

sales@metalfed.com | +91 9137898594 | Quotation Form | Reach Us